Note: if the header rail on the storm door comes too far down in the opening, you may have to add a block of wood under the wind chain bracket to get the chain to clear it when to door opens. Once you have gotten this far it should look like the picture below right now. Now with the storm door set to open as far as you want it, and with the storm door bracket mounted to the chain, extend the chain and bracket to the storm door, taking all of the slack out of the chain. When the chain is tight, mark the screw holes and install the bracket with the 2 smaller screws in the pack.
Now close the storm door and your chain should look something like this. If you are okay with that, stop here. It is a small spring with a loop at each end. I just feel that this is a little bit of insurance here if we keep any water from running down behind this.
Now I slide the drip cap over the top of the door. It should extend just beyond the left and right sides.
Then, Sue secures the drip cap with screws. Drip cap in place, we add the molding to our doorframe. Okay, so this piece of metal trim just snaps over this channel right here and conceals all of the screws we used to put this in.
Sue and I simply snap it in place all around the doorframe. Now here is something really helpful. The manufacturer includes a stick on template to show us exactly where to drill the holes for our latch set. Next I bore pilot holes, still using the template as a guide. Finally, with a larger bit, I make the final holes for the latch set. With the drilling completed, Sue attaches the latch to the door with screws. Now go back and do the top one. With the latch set installed we can now test the door.
Caper strips are used to hold the glass in place. Now squeeze this together. Push it up like that. Now that was easy. Feel the summer breezes or keep winter's blasts at bay, all the while admitting light after you install a new storm door. A storm door kit with good instructions makes assembly and installation a one-day project that's easy for the average home owner.
The result is a handsome storm door with a white aluminum frame and a beveled glass panel. Install the storm door hinges on the same side of the door frame as the existing door.
Use a power drill to drive the first screw into the single index hole the manufacturer has provided to position the frame properly. Install a self-centering drill bit to bore the remaining holes for the storm door hinges.
Its retractable sleeve lets it match the hinge holes to install storm door hinges precisely. Secure the hinges with screws. Measure the door height to determine the length of the hinge plate.
Mark the measurement on the hinge plate on the door and cut off the extra length with a hack saw before proceeding to install a storm door. Remove the glass and screen. Stand the storm door upright in the doorway with hinges on the left. To install your closers, you need to:. Keep reading so we can tell you more about storm door closers, how to install them, how they work, and how to adjust them.
We'll also discuss if these are required by the National Fire Prevention Association building code and for what purpose. Let's begin! Storm door closers are an essential part of your door hardware. They ensure the smooth operation of your door. You can control the level of speed and resistance according to your preference. They also ensure that your door is closed to enhance your security at home. It is common to see storm doors with only one door closer.
But some storm doors come with two closers to have enhanced protection against heavy winds. They add another layer of security to your door as they help ensure that it won't open recklessly when there's a storm.
In the end, it would depend on your personal preference and if you see the need to install double closers on your storm door.
Installing storm door closers, whether there's one or two of them, should be easy enough for the average DIYer. Here's a guide on how to do it. There are various types of door closers. Some closers are classified according to their weight or placement on the door or frame but the most common classification is the mechanism that they use for closing. Thus, you can find pneumatic door closers and hydraulic door closers.
The pneumatic closer is powered by spring tension and compressed air while the hydraulic closer makes use of spring tension and fluid or oil. They may use different elements but the general principle behind how they work is the same.
The component that's responsible for closing the door is the tension spring. The compressed air or fluid controls the rate of closing.
0コメント